Home   | About Us   | Gift Registry   | My Account   | Contact Us   | Blog   |
0 item(s) / Total: $0
cornpelletstoves.com

    AUTHORIZED DEALER with Quality and Service
 
Home > All Items

FORCED-AIR I (ONE) MULTI-FUEL FURNACE BOILER, STOVE 72,000 BTU/Hr

Part Number 12720227100
FORCED-AIR I (ONE) MULTI-FUEL FURNACE BOILER, STOVE 72,000 BTU/Hr
FORCED-AIR I (ONE) MULTI-FUEL FURNACE BOILER, STOVE 72,000 BTU/Hr
 
Email a friend Email a friend
Price
Your Price:  
$3,995.00
Availability:
Back Order.
Quantity
Add to Gift Registry
Description

FORCED-AIR I (ONE) MULTI-FUEL FURNACE BOILER

72,000 BTU/Hr.

Hot-water Coil Available as OPTIONS


Negative Draft Motor mounted on the rear
 allows burning of Wood Pellets
add OPTION of Hot-water Coils for Domestic Hot-water Heat\

Two-Stage Heat Exchanger Chambers

Multi-fuel and will burn Wood Pellets and Corn

    The FORCED-AIR I  (ONE)  of 72,000 BTU's per hour is one of the few FURNACES now on the market. The Negative Draft Rear Flue Motor Attachment enables it to  burn wood pellets.  It has Multiple Heat Exchangers in 2 stages.    DUCTWORK take-off at the top is for room-air heat and can hook into your ductwork. It is currently 14"ionround but it can be converted into 14" Square or 12" Round/Square.  .  The multi-fuel capability will allow it to burn corn and burn wood pellets. The Return Air Duct can be routed to the lower rear of the furnace where there is an intake grill and blower fan to suck air into the furnace.   Dampers fitting inside ducts are available as Options .  Large Hopper Bin of 115 lbs.   The standard flue exhaust vent is horizontal straight through-the-wall called a Concentric Flue Exhaust/Fresh Air VENT Kit. It blows hot gases outside the inside pipe and sleeves incoming fresh air into the combustion chamber from the outside concentric pipe.  The rear-mounted flue exhaust motor creating a negative draft will help eliminate hopper fires and smoke inside the hopper.  The option of a HOT-WATER COIL can produce heat for domestic hot-water for bathrooms and kitchens.  For other Options see Options paragraph.

    Buy a HOT WATER COIL (Option) and install it into upper part of the combustion chamber with the stainless steel pipes coming out the right-side wall.  These pipes pipe into your hot-water heater and  have the capability to heat both your home and domestic hot water used for bathrooms and kitchens. Buy and install this Option with this stove.  See picture.

    Option of just a STOVE is sold without the Ductwork, $3,595. 

    Note the Option of adding  LEGS in Matte Black and are $200 extra, ... otherwise you can just rest the unit on the floor, or build your own pedestal base (or use concrete blocks).  All ACCESSORIES are charged out separately and you can see them in the OPTIONS paragraph below.

    We sell another Model IV (Four) at 165,000 BTU/Hr for $2000 more. 

    See our other stoves, furnaces, boiler, and fireplace inserts in our website at cornpelletstoves.com.  Call us direct with an order Richard H. Dodge, Corn Stoves of Iowa, 1312 1st Avenue, NW, Cedar Rapids, Iowa 52405, 1-319-298-0500


PICTURE Descriptions ... left to right.

Top Row ... left to right

  1. Furnace Front View
  2. Furnace 3/4 View
  3. Furnace Side View
  4. Stove Only (No Ductwork)
  5. Stove Front and back
  6. Hopper Bin
  7. Combustion Chamber
  8. Rear-mounted Flue Exhaust Motor
  9. Concentric Horizontal Direct Vent Flue Exhaust Kit 
  10. Electronic Controls
  11. U-Shaped Hot Water Coil
  12. U and M-Shaped Hot Water Coil

OPTIONS

    OPTIONS available are as follows: (1) Legs available for $250 or furnace can just be put on blocks or rest on floor, (2) STOVE only without Ductwork $3,595, (3) Hot-Water Coils U-Shaped $295, M-Shaped $395,  (4) DUCT Take-off 14 Square $175 (5) DUCT Take-off of 12" Round or Square $200, (6) DUCT Back-Draft Damper 14 inch Square $175, (7) BACK-DRAFT DAMPER Plates (leaves) for Old Existing Furnace $175; (8) HOT-AIR Plenum Riser14" Round is 2 to 5 foot long $200, $350, (9) 14 inch Square take-off Tab Collar $150 (8) 14" Square Duct $150 per lineal foot up to 4', (9)Top-Mount 90 Degree DUCT-TURN w Register $350, (10) Cold-Air Return attachment option is available to feed into cold-air duct 20"x10" or 25x14" $300,  (10) Concentric Flue Exhaust Kit $385, (11) Flue Exhaust Kit 4-inch $485, (12) Rear-wall Fresh Air Kit $95, (13) Basement 6 Foot 4-inch Flue Extension $150, (14) Flue Exhaust 4 inch Stainless Steel FLEX Pipe extension $45/foot, (15) Corn Wood-Pellet Screener/Cleaner $85; (16) Hot-Ash Vac $295., (17) Power Outage Module 1500 Watts $295, (18) Power Outage Module AUTO-SWITCHING back and forth 12V  Bat to(from 120 VAC is $495. 

    Other Options are: FORCED-AIR MODEL  IV (FOUR) at 150,000 BTU/Hr add $2,000.

POWER OUTAGE BACKUP MODULE

    A Power-Outage Module (1500 watts) is available at $295 to supply 115 VAC to your crucial electrical devices ... a smart item to have as backup in power outages. Use this module for POWER OUTAGES and you can run it from any 12 VOLT BATTERY either a Car battery or a Deep Cycle Battery. It supplies 1500 WATTS of 115 VAC POWER with two outlets and battery cables are supplied. It will will run a variety of devices such as a corn stoves, wood-pellet stoves, furnaces, computers, appliances, lights, power to run appliances in camping, sump pumps. It even has a USB Type A outlet that allows charging of IPOD's, androids, apple, , and Cell Phones. SIZE: 10 inches Wide, 5 inches High, 15 inches Long, WEIGHT: 15 lbs.  Another Poer Outage Module is a Continuous Switching model back-and-forth from 115 VAC to 12V and vise versa, cost $495.

WARRANTY

    There is a 3 YEAR WARRANTY on the heat exchanger, combustion chamber, fire box, door, etc., and 1 YEAR WARRANTY on electronics. Re-sale by individuals or un-authorized dealers can not offer a valid warranty. Be careful from whom you buy. We are a Dealer specializing in corn stoves and can help you through your installation as well as and trouble shooting if necessary. Be careful as others do not have the capability to do that.

FLOOR LOCATION DUCT LAYOUT & FLUE EXHAUST LAYOUT

    There are two alternative layouts: (1) Short Hot-Air duct runs, long Flue Exhaust Pipe runs, and (2) Long Hot-Air Duct runs and short Flue Exhaust Pipe runs. We recommend (1) short Hot-Air Duct runs and long Flue Exhaust  Pipe runs.  The  reason is long Hot-Air Duct runs loose heat and result in a colder house and/or more fuel cost to heat the house.

BACK-DRAFT DAMPER SUGGESTIONS

    If you have two furnaces operating at the same time, both the Forced-Air I (One) and the old furnace will need Back-Draft Dampers installed on each furnace near the duct take-off on each furnace.  You need this to prevent reverse air flow when one furnace is running and the other isn't.. (Heated hot air can reverse back flow back through the furnace not running.)  We sell Aluminum drop leaves that are light weight, open and close easily, and save on horse power.  Beware some contractors make damper leaves out of galvanized steel and and the flaps move harder, robbing your furnace of horse power. Buy the back-draft dampers from us and you will get the right thing. If you are having difficulty making or finding a back-draft damper, then call us.

OPERATING AND INSTALLATION INSTRUCTIONS

. We recommend you run our Forced-Air I (One) as a primary furnace to achieve your desired temperature and use your old furnace as a backup only if needed.  You do that by dialing-down the thermostat to your old furnace about 5 Degrees lower than what you are comfortable with. Your Old furnace should only fire-up when the temperature falls 5 degrees, otherwise it will never run.

    Do NOT get rid of your Old Furnace but keep it as an emergency back-up. Use our Forced-Air I (One) as your primary furnace set to produce heat at 5 Degrees higher than your Old Furnace. The Forced-Air I (One} Unit does not need a thermostat to run effectively. 

    There are two Flue Exhaust Systems that can be used.  (1) Concentric Flue Exhaust System that sleeves Fresh Air into the combustion chamber flowing in between the inner and outer pipes (concentric).  This is a direct horizontal vent..  .(2) Rear Mounted Negative Flue Exhaust System  with one pipe and a rear-wall Fresh Air Kit.  We sell either system with the purchase. Note a Fresh Air Intake is necessary and can be used to avoid room air vacuum as well as draw oxygen-rich air in from the outside.

   We recommend customers using wood pellets to buy several different brands and test run them.  Premium Hardwood pellets with a  PFI Certification Seal are recommended.  PCI stands for Pellets Certification Institute.  You should also experiment with burning a mixture of wood pellets and corn.  Corn burns hotter. Burning strait corn should be 12% dry or less normally purchased from a corn-stove friendly farmer who dries his corn below 12% or lower.  Crushed Oyster Shell sprinkled in the hopper bin facilitates a cleaner burning and helps avoid any Clinker formation.

SHIPPING

    Note the shipping message is INCORRECT in that we ship all over the country.  Call us at 1-319-298-0500 for a shipping quote  Shipping is done by a commercial Freight Carrier and we ship 500 lbs in a carton strapped to a skid to the nearest large-city Main Terminal serving the customer's geographic area. The customer will drive a pickup truck over to the Main Terminal and they will load the item into your truck with a Fork-lift Truck.  We can ship to a local business in your town or nearby city that has a fork-lift and/or loading dock. Lumber Yards, Farm Equipment Cos, and local Manufacturers are good choices for fork-lift, loading-dock businesses. Call for a quote outside of the U.S. such as Canada.


SPECIFICATIONS

    Heat Output Model I is 72,000 BTU/hr with 110 lbs Hopper Bin, 5 Heat Range knob settings.  It has a 500 CFM Room Air Blowers. Heating Capacity for Model I are up to 3,500 Square Feet. Duct Take-Offs (Options) either 12" Round, 14" Square, or 8"x16" Rectangular. Cold Air return has a Filter slot. The Flue Exhaust System is either a concentric Direct Vent System or a Reat Mounted Flue Exhaust Motor with a rear-wall Fresh Air Kit. Weight of the Model I (One) Furnace ion a crate/pallet is around 650 lbs. Dimensions of Model I (ONE) are: 29-1/2 inches Wide, 37 inches High, 27 inches Deep. Add 6" high for Legs. , Electrical 115 VAC, 10 Amps, 60 Hz, a POWER OUTAGE Module is available. It was Safety Tested by Warnock Hersey and Listed to CAN/CSA B366.1-M91, ULC-C 391-99. Manufacturer: American Heating Systems

QUESTIONS

    For questions, comments, quotes on shipping, see our other stoves, furnaces, boiler, and fireplace inserts in our website at cornpelletstoves.com.  Call us direct with an order Richard H. Dodge, Corn Stoves of Iowa, 1312 1st Avenue, NW, Cedar Rapids, Iowa 52405, 1-319-298-0500.

Related Items
AIR FLOW METER, ANEMOMETER, Measures AIR FLOW CFM
AIR FLOW METER, ANEMOMETER, Measures AIR FLOW CFM
Your Price: $195.00
CHIMNEY-TOP DAMPER  replaces WOOD FIREPLACE DAMPER
CHIMNEY-TOP DAMPER replaces WOOD FIREPLACE DAMPER
Your Price: $175.00
CORN MOISTURE TESTER STOVE FURNACE BOILER
CORN MOISTURE TESTER STOVE FURNACE BOILER
Your Price: $175.00
FLUE GAS THERMOMETER
FLUE GAS THERMOMETER
Your Price: $45.00
FORCED-AIR THREE CORN WOOD PELLET MULTIFUEL FURNACE STOVE, 120,000 BTU/Hr
FORCED-AIR THREE CORN WOOD PELLET MULTIFUEL FURNACE STOVE, 120,000 BTU/Hr
Your Price: $6,995.00
WINCHESTER MAGNUM FIREPLACE INSERT, WIN-ACI, burns CORN, PELLETS, MULTI-FUEL, 45-50,000 BTU/Hr
WINCHESTER MAGNUM FIREPLACE INSERT, WIN-ACI, burns CORN, PELLETS, MULTI-FUEL, 45-50,000 BTU/Hr
Your Price: $3,295.00
Browse Similar Items